THE TECHNOLOGY EXPLAINED

How PoE lighting actually works.

A lighting network sends low-voltage DC power and control data through Ethernet cable to compatible LED lighting devices. The result is a connected, configurable lighting system.

Explore installation diagrams
SYSTEM OVERVIEW

Power. Data. Control. One planned architecture.

A simplified representation of how switches, structured cabling, fixtures and control software fit together.

COMPONENT-BY-COMPONENT / VISUAL REFERENCE

See how each part connects. Step by step.

Follow the conceptual power and data path for each item. Every diagram labels the cable type between components and the installation checks. These are educational schematics, not tested combination approvals, electrical plans, or manufacturer installation instructions.

01 / SYSTEM CORE

UniFi switch and rack power

View cable guide ↗
  1. Step 1 Install and secure the correctly rated network rack and switch.
  2. Step 2 Provide the switch with its rated AC supply; use a separately sized UPS if outage runtime is required.
  3. Step 3 Test the solid-copper Cat6A PoE channel before connecting the exact driver.

Design limit: A 90 W-rated port and total switch PoE budget are separate limits. AC work belongs to appropriately licensed trades.

02 / STRUCTURED CABLING

From the switch to a ceiling driver

View cable guide ↗
  1. Step 1 Select the correct riser, plenum or outdoor-rated jacket for each pathway.
  2. Step 2 Run a continuous four-pair solid-copper Cat6A home run; support, label and terminate it.
  3. Step 3 Test the channel, review cable bundle temperature/length, then confirm power negotiation at the driver.

Design limit: 100 m is the typical Ethernet channel maximum, not permission to ignore device power loss or environmental derating.

03 / DRIVER / CONTROL NODE

UPD-type lighting driver and its output

View cable guide ↗
  1. Step 1 Use only the driver specified for the exact lighting fixture and configuration.
  2. Step 2 Mount the driver per the manufacturer, with access for service and correct ventilation.
  3. Step 3 Connect the correct vendor-specified Cat6 lead/splitter from the driver to the LED fixtures. Verify output and dimming.

Design limit: PoEWit says UPD-to-fixture cables must be Cat6 or better, max 25 ft, not slim Cat6; do not swap driver types.

04 / INDOOR CEILING LUMINAIRE

2×2 or 2×4 commercial LED ceiling panel

View cable guide ↗
  1. Step 1 Confirm ceiling grid, luminaire mounting, photometric requirements and cable pathway.
  2. Step 2 Home-run Cat6A to the tested PoE driver installed in an accessible location.
  3. Step 3 Use the exact factory-tuned LED output/cable and splitter; mount and verify the panel, dimming and restart.

Design limit: Concept only. The pictured current panel/driver models are NOT verified with UniFi; the drawing is not an approved installation wiring diagram.

05 / RECESSED LIGHTING

Recessed downlight / tunable fixture

View cable guide ↗
  1. Step 1 Identify the exact trim, wattage, white channel count and factory-tuned driver model.
  2. Step 2 Install the correct mount, driver and cable route within the ceiling; maintain service access.
  3. Step 3 Connect only the specified splitter/output leads, then test each fixture, dimming and power recovery.

Design limit: Different RX-1 / RT-1 driver channel arrangements are not interchangeable. UniFi + PoEWit pairing is not validated.

06 / EXTERIOR LIGHTING

Outdoor PoE wall pack and weatherproof pathway

View cable guide ↗
  1. Step 1 Confirm fixture weather rating, height, local egress needs and penetrations.
  2. Step 2 Run outdoor-rated copper cable through an approved pathway with sealed transitions and appropriate weatherproof termination.
  3. Step 3 Mount the wall pack, verify any downstream PoE pass-through budget, and test after rain/temperature exposure as required.

Design limit: The 35 W fixture wattage does NOT validate upstream pass-through draw or 90 W PoE negotiation. No UniFi pairing approved.

07 / AUTOMATION

Occupancy and daylight sensor control path

View cable guide ↗
  1. Step 1 Select sensor coverage and location, away from sources of false triggering.
  2. Step 2 Home-run Cat6 to the sensor's specified PoE port/class; test and label the connection.
  3. Step 3 Configure the compatible lighting manufacturer's controller and test occupancy, daylight, manual override and offline behavior.

Design limit: UniFi manages PoE ports; lighting scenes/dimming depend on an independent validated control ecosystem.

08 / OPTIONAL DC POWER REDUNDANCY

Pro XG switch with USP-RPS failover

View cable guide ↗
  1. Step 1 Check the exact Pro XG model includes a supported RPS input.
  2. Step 2 Connect approved proprietary UniFi RPS cable; keep it separate from Ethernet/PoE.
  3. Step 3 Calculate simultaneous load against the shared 52 V/600 W and 11.5 V/350 W RPS rails; test failover and recovery.

Design limit: USP-RPS does not add PoE output budget or supply battery backup. It may not sustain a fully loaded switch.

09 / INTEGRATED POWER REDUNDANCY

Campus 24 PoE hot-swappable PSU arrangement

View cable guide ↗
  1. Step 1 Install manufacturer-approved 600 W PSU modules in the correct Enterprise Campus chassis bays.
  2. Step 2 Plan independent AC feeds or UPS-backed paths as required; use serviceable cord routing.
  3. Step 3 Set the intended mode: 1,050 W shared or 450 W redundant available PoE budget; document failover and replaceability.

Design limit: Do not use USP-RPS with Campus. Internal PSU modules are not RJ45/cabling; PoE endpoints still require their own copper Ethernet runs.

Only qualified products go into final Secure Luma specifications.

The exact UniFi switch, LED driver, luminaire, lighting-control platform and cable system must pass a documented end-to-end acceptance test before being recommended. See Secure Luma’s equipment qualification requirements. Do not connect conventional line-voltage fixtures to Ethernet or assume different constant-current drivers can be interchanged.

See cable requirements by product →
SYSTEM COMPONENTS

The five pieces of an intelligent PoE lighting deployment.

Every component needs to work together. A lighting switch alone is not a complete lighting system.

01

Power sourcing equipment (PSE)

A rated PoE switch or dedicated PoE lighting controller converts and distributes power through Ethernet ports. Design must consider both per-port limits and the switch's total available wattage.

02

Structured Ethernet cabling

Appropriately specified Cat6 or Cat6A cabling carries power and data to lighting devices. Cable gauge, length, bundling and termination quality can affect efficiency and performance.

03

Compatible LED drivers and luminaires

Purpose-built PoE fixtures—or approved nodes/drivers from the chosen ecosystem—convert supplied power into appropriate LED drive conditions. Not every conventional LED fixture connects directly to an RJ45 cable.

04

Sensors and lighting control

Where supported, occupancy sensors, daylight sensors, dimming and scheduling adjust light output according to space usage and daylight availability.

05

Software and network management

A controller or management platform helps teams configure zones and monitor supported equipment. Remote access needs appropriate network security and vendor support.

ENGINEERING THE DETAILS

Power budgets matter more than the switch label.

The system must supply enough power at the device after considering cable loss and equipment overhead. High-bay lighting may need multiple ports, specific PoE lighting hardware or a different power architecture.

We assess fixture output requirements, available hardware and installation constraints before recommending a design.

Review My Facility
1

Define illuminationTarget light levels, output and distribution

2

Match the PoE standardPort wattage and total switch budget

3

Design the cable pathsGauge, length, heat and terminations

4

Verify operational needsCodes, emergency lighting and controls

COMMON QUESTIONS

PoE lighting, explained simply.

Can any PoE switch power warehouse LED fixtures?

No. A fixture must be compatible with the available PoE power delivery and any required controller or driver. Some high-output luminaires exceed what a single standard PoE port can deliver.

Is a dedicated Ethernet cable required for each light?

Many deployments have a home-run cable to each luminaire or lighting node, while some ecosystems use gateways or shared nodes. The selected hardware determines the physical layout.

Does PoE lighting need an internet connection?

Local operation can be supported without continuous internet access, depending on the chosen platform. Internet is typically needed for off-site monitoring and some cloud features.

Can existing line-voltage lighting be retrofitted?

Sometimes. Retrofit feasibility depends on fixture/driver compatibility, existing cabling, control requirements and the scope of the work. It is not a direct plug-and-play conversion for every fixture.

NEXT STEPS

Compare real system components and compatibility.

Understand port power budgets, PoE fixtures, cabling and control options before specifying equipment.

LET'S PLAN YOUR NEXT PROJECT

Better lighting starts with a better network plan.

Tell us about your facility and we'll discuss whether a PoE-powered lighting approach makes sense for your space.

Discuss a Project